EPRO PR6426/000-110 CON021 Eddy Current Sensor – Obsolete PR6426 Series Spare Part

Technical Dossier

Product Details And Specifications

EPRO PR6426/000-110 CON021 Eddy Current Sensor – Obsolete PR6426 Series Spare Part

When the PR6426/000-110 CON021 eddy current sensor fails in a running plant, the consequences extend far beyond a single component replacement. This sensor is a core element of shaft vibration and position monitoring in rotating machinery protection systems — turbines, compressors, pumps — that have been operating reliably for decades on EPRO (now Bently Nevada / Baker Hughes) architecture. A forced system migration triggered by one unavailable sensor can cost a facility anywhere from several hundred thousand to several million USD in engineering, downtime, recommissioning, and revalidation. DriveKNMS holds verified stock of this discontinued part. That stock is finite.

Technical Specifications

Note: Electrical parameters such as sensitivity, gap range, and frequency response are model-configuration-specific. Contact us with your full system documentation for cross-verification before ordering.

Solving the Discontinued Hardware Crisis

The PR6426 series was engineered for precision proximity measurement in industrial rotating machinery protection — a function that cannot be approximated by a generic substitute without full system recalibration. These sensors operate as part of a tightly coupled measurement chain: sensor, extension cable, and signal conditioner (such as the CON021 module) are calibrated as a matched set. Replacing one element with a non-original component invalidates the calibration and, in safety-critical applications, the protection system certification.

Plant managers facing the retirement of EPRO-based monitoring infrastructure confront a binary choice: invest in a full platform migration — with all associated engineering hours, downtime scheduling, and revalidation costs — or source the original spare part and extend the asset's productive life. For facilities running turbines or compressors with 15–30 years of remaining mechanical life, the economics of maintaining the original monitoring architecture are straightforward. A single verified PR6426/000-110 CON021 unit, properly installed, can defer a six- or seven-figure capital expenditure by five to ten years.

The supply window for this part is closing. OEM channels have been exhausted. Secondary market availability is declining as installed base units age out. Facilities that have not yet established a strategic spare inventory for their EPRO sensor chains are operating with an unquantified replacement risk.

Condition & Reliability Assurance

Every PR6426/000-110 CON021 unit processed by DriveKNMS passes a structured 5-step quality protocol before it is offered for sale:

• Step 1 – Visual and mechanical inspection: Housing integrity, connector condition, and cable jacket assessment. Units with physical damage to the probe tip or connector body are rejected.
• Step 2 – Electrolytic capacitor assessment: Internal conditioning circuitry is inspected for capacitor aging, leakage, or bulging — a primary failure mode in sensors stored beyond five years.
• Step 3 – Pin and contact corrosion check: All electrical contacts are examined under magnification. Oxidation or corrosion on signal pins is a disqualifying condition.
• Step 4 – Firmware and configuration verification: Where applicable, CON021 conditioner module firmware version and configuration state are verified against known-good references.
• Step 5 – Functional output test: Sensor output characteristics are verified against published EPRO specifications using calibrated test equipment.

Units that do not pass all five steps are not listed for sale. Condition grade (new surplus, tested serviceable, or refurbished) is disclosed at the time of quotation.

Key Features for System Maintenance

• Drop-in replacement: The PR6426/000-110 CON021 is a direct physical and electrical replacement for the same part number in existing EPRO installations. No mechanical modification is required.
• No reprogramming required: When replacing a like-for-like unit within a matched sensor chain, the monitoring system does not require reconfiguration. Calibration verification is recommended but system engineering is not.
• Avoids engineering reconstruction costs: Substituting a non-original sensor into an EPRO protection system requires full recalibration of the measurement chain and, in many jurisdictions, re-certification of the protection function. Using the original part number eliminates this cost entirely.
• Long-term asset protection: Maintaining a two- to three-unit strategic spare inventory for critical sensor positions is the lowest-cost insurance available against unplanned production loss from sensor failure.

FAQ

What warranty applies to discontinued parts?
DriveKNMS provides a 90-day warranty against defects in materials and workmanship on all tested and refurbished units. New surplus units carry a 180-day warranty. Warranty terms are confirmed in writing at the time of sale.

How do I know the unit is genuine and not counterfeit?
All units are sourced from documented industrial decommissioning projects, authorized distributors, or verified surplus channels. Provenance documentation is available on request. We do not source from unverified brokers.

Should I buy more than one unit?
For any sensor position classified as critical — meaning its failure triggers a machine trip or production stop — a minimum of one cold spare per installed position is the standard industry practice. Given the declining availability of PR6426 series components, purchasing two to three units now is a measurably lower-cost decision than sourcing under emergency conditions in 12 to 24 months.

Can you source other EPRO PR6426 variants?
Yes. DriveKNMS maintains sourcing relationships for multiple PR6426 configurations. Contact us with your full part number, including cable length suffix and conditioner type, for availability and lead time.

© 2026 DriveKNMS. Status: DRAFT