Bently Nevada 330876-02-10-01-00 Proximity Probe – Obsolete 3300 XL Spare Part

Model: 330876-02-10-01-00

Series 3300 XL
Model 330876-02-10-01-00
RFQ-ready model route Obsolete and surplus sourcing Export follow-up by model list

Product Overview

Commercial availability is handled through direct RFQ, model verification and export-oriented follow-up rather than public cart checkout.

Datasheet Preview

Datasheet Preview

Use attached product manuals when available. If the manual is not public yet, request the full file directly through RFQ.

Request Full Manual

Commercial Path

Use This Page To Confirm The Model, Then Move To RFQ

Product pages on DRIVEKNMS are designed to verify model, brand and series first, then move the buyer into one clean quotation path.

Technical Dossier

Product Details And Specifications

Bently Nevada 330876-02-10-01-00 Proximity Probe – Obsolete 3300 XL Spare Part

RFQ support for obsolete parts: Send the model number, required quantity and destination so DriveKNMS can confirm sourcing options before quotation.

Technical Specifications

Parameter Value
Part Number 330876-02-10-01-00
Manufacturer Bently Nevada (Baker Hughes)
Series 3300 XL
Type Eddy-Current Proximity Probe
Probe Length 50 mm
Cable Connector Integral armored cable
Compatible Driver/Proximitor 3300 XL 8mm Proximitor System
Typical Application Radial vibration, axial position, speed measurement on rotating machinery
Discontinuation Status Discontinued – No longer in active production by OEM
Country of Origin United States

Note: Electrical parameters (sensitivity, gap voltage, frequency range) are system-dependent and calibrated as part of the complete 3300 XL transducer system. Confirm compatibility with your specific Proximitor module before installation.

Solving the Discontinued Hardware Crisis

The Bently Nevada 3300 XL platform has been the industry standard for machinery protection on steam turbines, compressors, pumps, and generators for decades. Its architecture — built around matched probe, extension cable, and Proximitor assemblies — means that a single failed probe cannot simply be substituted with an off-the-shelf alternative without recalibration, re-engineering, or in many cases, a full system replacement.

Condition & Reliability Assurance

Sourcing discontinued instrumentation from the secondary market carries legitimate quality concerns. DriveKNMS applies a structured 5-step inspection protocol to every 3300 XL proximity probe before it is offered for sale:

  • Step 1 – Visual and Mechanical Inspection: Probe tip, cable jacket, and connector are examined for physical damage, corrosion, and mechanical deformation. Units with compromised cable armor or bent probe tips are rejected.
  • Step 2 – Electrolytic Capacitor Assessment: Internal passive components, including any electrolytic capacitors in the probe circuit, are evaluated for signs of aging, leakage, or drift that could affect sensitivity linearity.
  • Step 3 – Connector and Pin Integrity Check: All connector pins are inspected under magnification for oxidation, fretting corrosion, and mechanical wear. Pin corrosion is a primary failure mode in stored instrumentation and is treated as a disqualifying defect.
  • Step 4 – Firmware and Labeling Verification: Part number markings, date codes, and any embedded identification are cross-referenced against OEM documentation to confirm authenticity and correct revision level.
  • Step 5 – Functional Verification: Where test equipment permits, probe impedance and basic electrical continuity are verified against known-good reference values for the 330876 series.

Units that pass all five stages are classified as Tested Surplus or New Surplus depending on their physical condition and provenance documentation. Condition is disclosed in full at the time of quotation.

Key Features for System Maintenance

  • Drop-in replacement: The 330876-02-10-01-00 is a direct OEM-equivalent component. Installation does not require reprogramming of the Proximitor module or modification of existing gap voltage setpoints, provided the replacement probe is of the same revision.
  • No engineering rework: Unlike a platform migration, substituting a like-for-like probe preserves all existing trip and alarm setpoints, eliminating the need for costly safety system revalidation.
  • Avoids capital project trigger: A single probe replacement keeps the 3300 XL system operational and defers the decision to migrate to a modern platform — a decision that carries significant budget, schedule, and operational risk.
  • Maintains SIS integrity: For facilities where the 3300 XL is integrated into a Safety Instrumented System, maintaining original hardware avoids the revalidation burden associated with hardware substitution under IEC 61511.
  • Documented chain of custody: DriveKNMS provides sourcing documentation with each unit to support maintenance records and audit requirements.

Q: How do I know the unit is genuine and not a counterfeit?
A: Every unit is inspected against OEM part number markings and physical construction standards. Where available, original packaging and documentation accompany the unit. We do not sell units that fail authenticity verification.

Q: Can this probe be used with the Bently Nevada 3500 system?
A: The 3300 XL and 3500 series use different Proximitor architectures. Cross-compatibility requires engineering review. This probe is specified for use within the 3300 XL transducer system only.

Continue The Model Path

Use system, brand and series routes to compare related published models.

Move from this exact model into the matching system hub, brand archive, model-family archive or lifecycle sourcing route before sending a final RFQ list.

WhatsApp Prefilled Inquiry Email sale@driveknms.com Phone +86 18359293191 Top Back To Top