Mitsubishi FR-CV-H30K Regenerative Converter Unit – Obsolete FR-CV Series Spare Part

Technical Dossier

Product Details And Specifications

Mitsubishi FR-CV-H30K Regenerative Converter Unit – Obsolete FR-CV Series Spare Part

DriveKNMS reviews sourcing options for this model during RFQ handling before quotation.

RFQ support for obsolete parts: Send the model number, required quantity and destination so DriveKNMS can confirm sourcing options before quotation.

Technical Specifications

Note: Electrical parameters not listed above have not been independently verified by DriveKNMS. Specifications should be cross-referenced against the original Mitsubishi FR-CV Instruction Manual (IB-0600143) before installation.

Solving the Discontinued Hardware Crisis

The FR-CV-H30K was designed as the regenerative front-end for Mitsubishi's FR-A500 and FR-A700 high-voltage inverter platforms. Its role is not decorative — it converts braking energy back into the supply grid rather than dissipating it as heat through resistor banks. In applications such as overhead cranes, winding machines, centrifuges, and test rigs with frequent deceleration cycles, the FR-CV unit is a load-bearing component of the energy management architecture.

No current Mitsubishi product is a pin-compatible, firmware-compatible drop-in replacement for the FR-CV-H30K within an existing FR-A500/A700 cabinet. Migrating to a current-generation FR-A800 or FR-F800 platform requires new drive hardware, new cabling, updated PLC I/O mapping, and in many cases, updated motor protection coordination studies. Facilities operating under tight capital budgets or with production schedules that cannot absorb a multi-week commissioning window face a genuine operational constraint.

Maintaining a verified spare FR-CV-H30K on the shelf eliminates that constraint. Mean time to repair drops from weeks to hours. The production asset — whether a crane bridge, a rolling mill stand, or a test dynamometer — continues operating on its existing validated configuration without engineering intervention.

Condition & Reliability Assurance

DriveKNMS applies a 5-step inspection protocol to all discontinued converter units before they are offered for sale. This process is designed around the specific failure modes that accumulate in power electronics over extended storage or service life.

Step 1 – Electrolytic Capacitor Assessment: DC bus capacitors and filter capacitors are tested for capacitance retention and equivalent series resistance (ESR). Units with capacitors showing more than 20% capacitance loss or elevated ESR are either recapped with equivalent-rated components or withheld from sale.

Step 2 – Firmware & Control Board Verification: Where accessible, firmware version is recorded and cross-referenced against known stable releases for the FR-CV series. Control board logic is verified through functional bench testing.

Step 3 – Pin and Terminal Corrosion Inspection: All connector pins, bus bar terminals, and control terminals are inspected under magnification for oxidation, fretting corrosion, and mechanical deformation. Affected contacts are cleaned or the unit is flagged for disclosure.

Step 4 – Insulation Resistance Check: Power circuit insulation resistance is measured to confirm integrity of internal wiring and bus isolation.

Step 5 – Documentation and Traceability: Each unit dispatched carries an inspection record noting condition grade, test results, and any remediation performed. This record supports your internal maintenance documentation requirements.

Key Features for System Maintenance

The FR-CV-H30K installs as a direct physical and electrical replacement within an existing FR-A500/A700 drive cabinet. There is no firmware reconfiguration required on the inverter side, no PLC parameter changes, and no motor re-tuning. The unit connects to the same DC bus terminals and uses the same control signal interface as the original factory installation.

This drop-in compatibility is the defining operational advantage of sourcing an original FR-CV-H30K rather than attempting to engineer an alternative solution. Alternative approaches — such as installing a generic active front-end unit from a different manufacturer — require engineering time, compatibility validation, and in regulated industries, re-certification of the modified drive system. None of those costs apply when the original part is available.

For facilities managing multiple FR-A500/A700 installations across a site, holding two FR-CV-H30K units in bonded stores provides coverage for the full installed base without any per-machine engineering overhead.

How do I confirm the unit is new surplus or quality-refurbished, not field-pulled scrap?
Every unit is graded before listing. New surplus units are identified as such and have not been installed in service. Refurbished units carry the full 5-step inspection record described above. DriveKNMS does not sell uninspected field-pull units. Condition grade is stated explicitly in the order confirmation.

Can you source specific serial number ranges or production dates?
Serial number and production date information is provided for each available unit upon request before purchase. Contact us with your requirements.