Bosch KM3300 Modules KM 3300-T 054915-103 KM3300
Bosch KM 3300-T 054915-103 KM3300 is listed for 3300 RFQ review. Confirm quantity, condition and destination before quotation.
Model: 330102-00-25-50-11-00
Product Overview
Commercial availability is handled through direct RFQ, model verification and export-oriented follow-up rather than public cart checkout.
Datasheet Preview
Use attached product manuals when available. If the manual is not public yet, request the full file directly through RFQ.
Commercial Path
Product pages on DRIVEKNMS are designed to verify model, brand and series first, then move the buyer into one clean quotation path.
Technical Dossier
RFQ support for obsolete parts: Send the model number, required quantity and destination so DriveKNMS can confirm sourcing options before quotation.
| Parameter | Value |
|---|---|
| Part Number | 330102-00-25-50-11-00 |
| Brand | Bently Nevada |
| Series | 3300 XL 8mm Proximity Transducer System |
| Type | Eddy-Current Proximity Probe |
| Probe Length | 25 cm (250 mm) |
| Cable Length | 50 cm extension cable |
| Thread Size | 8mm |
| Connector Type | 11-pin (per part number suffix) |
| Compatible Drivers | 3300 XL Series drivers (e.g., 330180) |
| Compatible Monitors | 3300/16, 3500 Series (with appropriate driver) |
| Discontinuation Status | Discontinued by Bently Nevada / Baker Hughes |
| Country of Origin | United States |
Note: Electrical parameters such as sensitivity (mV/mil) and gap voltage are system-calibrated values. DriveKNMS does not publish unverified specifications. Consult your system documentation or contact us for calibration data.
The Bently Nevada 3300 Series proximity transducer system was the industry standard for shaft vibration and position monitoring on rotating machinery — steam turbines, gas compressors, centrifugal pumps — for decades. Many of these systems remain in active service, embedded in plant infrastructure that was engineered around their specific signal characteristics and connector formats.
Baker Hughes (which absorbed Bently Nevada) has progressively discontinued 3300 Series components in favor of the 3500 platform. The 330102-00-25-50-11-00 probe is among the parts no longer available through standard distribution channels. For facilities that have not migrated — and many have not, due to the capital cost and operational risk of doing so — this creates a direct asset protection problem. A failed probe with no replacement available means either running the machine unmonitored (a safety and compliance violation in most jurisdictions) or initiating an emergency system upgrade under the worst possible conditions.
How to Extend Your 3300 Series System Life by 5–10 Years Without a Full Platform Migration
Plant managers facing pressure to retire legacy Bently Nevada 3300 infrastructure have a viable alternative to full system replacement. The following strategy has been applied successfully in petrochemical, power generation, and heavy manufacturing environments:
1. Conduct a full spare parts audit. Identify every 3300 Series component — probes, extension cables, drivers, monitors — currently installed and cross-reference against known discontinued part numbers. Quantify your exposure before a failure forces the decision.
3. Source from verified secondary market suppliers. Original Bently Nevada 3300 Series parts are available through specialist distributors. Verify that suppliers can provide traceability documentation and perform basic functional checks before dispatch review.
4. Defer migration to a planned outage window. A 3300-to-3500 migration is a significant engineering project. Executing it during an unplanned shutdown multiplies cost and risk. Maintaining spare parts inventory buys the time to schedule migration properly — on your terms, not the machine's.
5. Document your installed base. Maintain a living record of probe serial numbers, installation dates, and gap voltage readings at commissioning. This data is essential for condition-based replacement decisions and reduces the risk of running a degraded probe to failure.
DriveKNMS applies a structured 5-step quality process to all discontinued parts before dispatch review:
Step 1 – Visual and Mechanical Inspection: Probe tip, cable jacket, and connector pins are inspected for physical damage, corrosion, and thread integrity. Parts with compromised cable insulation or bent pins are rejected at this stage.
Step 2 – Electrolytic Capacitor Assessment: For any associated driver or signal conditioning electronics, electrolytic capacitors are assessed for age-related degradation. Capacitor failure is the leading cause of intermittent signal faults in legacy proximity systems.
Step 3 – Pin and Contact Corrosion Check: Connector contacts are inspected under magnification. Oxidation on signal pins introduces resistance that shifts calibration. Affected contacts are cleaned or the part is rejected.
Step 4 – Firmware and Configuration Verification (where applicable): For programmable components in the 3300/3500 ecosystem, firmware versions are verified against known-good baselines.
Step 5 – Functional Verification: Where test equipment permits, probes are verified for basic eddy-current response before packaging.
Parts that do not pass all five steps are not offered for sale. Condition grade (New, Refurbished-Grade-A, or Tested-Used) is disclosed on every order confirmation.
The 330102-00-25-50-11-00 is a direct drop-in replacement for the same part number in any 3300 XL 8mm proximity transducer system. No reprogramming is required. No reconfiguration of the monitoring system is necessary. The probe installs to the same mechanical interface, connects to the existing extension cable or driver, and restores the measurement channel to its original specification.
For facilities managing multiple machine trains, the ability to execute a probe replacement without specialist support is a direct reduction in maintenance labor cost and a measurable improvement in mean time to repair (MTTR).
Q: How do I know the part is genuine and not a counterfeit?
A: We source from verified channels and can provide available traceability documentation on request. Physical markings, label formats, and connector specifications are cross-checked against known-authentic references. We do not sell parts we cannot verify.
Q: Can this probe be used with the Bently Nevada 3500 Series monitors?
A: The 3300 XL 8mm probe system is compatible with 3500 Series monitors when used with the appropriate driver module. Confirm your driver part number before ordering if you are integrating into a 3500 rack.
Continue The Model Path
Move from this exact model into the matching system hub, brand archive, model-family archive or lifecycle sourcing route before sending a final RFQ list.