GE DS200RTBAG3AEB Relay Board – Obsolete Mark V Spare Part

Model: DS200RTBAG3AEB

Series Mark V
Model DS200RTBAG3AEB
RFQ-ready model route Obsolete and surplus sourcing Export follow-up by model list

Product Overview

Commercial availability is handled through direct RFQ, model verification and export-oriented follow-up rather than public cart checkout.

Datasheet Preview

Datasheet Preview

Use attached product manuals when available. If the manual is not public yet, request the full file directly through RFQ.

Request Full Manual

Commercial Path

Use This Page To Confirm The Model, Then Move To RFQ

Product pages on DRIVEKNMS are designed to verify model, brand and series first, then move the buyer into one clean quotation path.

Technical Dossier

Product Details And Specifications

GE DS200RTBAG3AEB Relay Board – Obsolete Mark V Spare Part

RFQ support for obsolete parts: Send the model number, required quantity and destination so DriveKNMS can confirm sourcing options before quotation.

Technical Specifications

Parameter Detail
Part Number DS200RTBAG3AEB
Manufacturer GE (General Electric)
Series Mark V Turbine Control System
Board Function Relay Terminal Board
OEM Discontinuation Status Discontinued – No longer manufactured or supported by GE
Compatible Platform GE Mark V (TMR and Simplex configurations)
Country of Origin United States
Condition Available New surplus / Tested refurbished (specified at time of order)

Note: Electrical parameters such as relay contact ratings and board-level voltage specifications vary by revision. DriveKNMS will confirm exact revision details upon inquiry. No parameters are published here that cannot be verified against physical hardware.

Solving the Discontinued Hardware Crisis

The GE Mark V was the dominant turbine control platform across gas, steam, and combined-cycle power generation from the late 1980s through the 2000s. Thousands of units remain in active service globally — in power plants, petrochemical facilities, and industrial co-generation sites — because the cost and risk of replacing a functioning control system cannot be justified on a depreciation schedule alone.

The DS200RTBAG3AEB relay board sits within the Mark V's I/O and relay output architecture. Its function is direct: it interfaces control logic outputs with field devices — actuators, solenoids, and protective relay circuits. There is no modern drop-in equivalent that can be installed without engineering rework. When this board fails, the turbine unit it controls goes offline. In a peaking plant or a facility without redundant generation, that means lost revenue measured in hours, not days.

How to extend your Mark V asset life by 5–10 years without a control system replacement:

Condition & Reliability Assurance

Sourcing a discontinued board from the secondary market carries inherent risk. DriveKNMS applies a structured 5-step qualification process to every Mark V board before it is offered for sale:

  1. Visual and mechanical inspection: Full board examination for physical damage, burnt components, cracked solder joints, and connector pin condition. Boards with evidence of field damage beyond normal wear are rejected at this stage.
  2. Electrolytic capacitor assessment: Capacitors are the primary age-related failure point on boards of this era. Each electrolytic capacitor is checked for bulging, leakage, and ESR (equivalent series resistance) deviation. Boards with degraded capacitors are either recapped or rejected.
  3. Pin and connector corrosion check: Edge connectors and relay socket pins are inspected under magnification. Oxidation is treated; boards with pitting or structural corrosion on contact surfaces are not offered as functional spares.
  4. Firmware and revision verification: The board's revision marking is documented and cross-referenced against the customer's system configuration where possible. Revision mismatches are flagged before dispatch review, not after.
  5. Functional test (where test fixture available): Boards are powered and exercised through available test protocols. Test results are documented and available to the customer on request.

Key Features for System Maintenance

  • Drop-in replacement: The DS200RTBAG3AEB installs directly into the existing Mark V cabinet slot. No rewiring, no I/O remapping, no software reconfiguration is required when the replacement board matches the installed revision.
  • No reprogramming required: Mark V relay boards do not carry application-specific firmware. Configuration resides in the controller, not the board. Replacement does not trigger a re-commissioning event.
  • Avoids engineering rework costs: A board-level replacement keeps your existing control system architecture intact. There is no need to engage a controls engineering firm, no need to update loop drawings, and no need to schedule a full functional acceptance test.
  • Preserves existing operator familiarity: Your operations team knows the Mark V HMI. Maintaining the existing platform avoids retraining costs and the operational risk that accompanies any new system introduction.

Q: How are RFQ terms confirmed?
A: Quantity, required condition, documentation needs, destination and sourcing route are confirmed during RFQ review before quotation.

How do I know the board is genuine and not counterfeit?
All boards sourced by DriveKNMS are inspected for OEM markings, PCB layer consistency, and component date codes. Boards that show evidence of re-marking or non-OEM component substitution are rejected. We do not sell boards we cannot verify as genuine GE manufacture.

Continue The Model Path

Use system, brand and series routes to compare related published models.

Move from this exact model into the matching system hub, brand archive, model-family archive or lifecycle sourcing route before sending a final RFQ list.

WhatsApp Prefilled Inquiry Email sale@driveknms.com Phone +86 18359293191 Top Back To Top